1. The cone is crooked and out of shape in my works, produced at random.
    在我的作品里圆锥体是弯曲变形，随机产生的。

2. Seed scales appressed, woody or leathery, variable in shape and size, with 2 seeds adaxially, persistent or deciduous after cone maturity.
    种鳞贴伏，木质或革质，外形易变和尺寸，具2种子，在孢子叶球成熟之后落叶的宿存或。

3. When cutting tool roaled of spindle''s hole by manipulator or other ways, the pull nail behind of knife hilts is sent to ahead of tension bar of spindle. When receives the clamps signal, the pressure oil is passed over the oil cylinder left cavity of the spindle rear part, the piston to the right migration, tension bar also to right migration by small dish shape spring function, the stell ball of ahead circumference of the tension bar shrink the distribution diameter by spindle''s cone hole''s force, holds on the knife hilts and pull nail colsely.
    当刀具由机械手或用其他方法装到主轴孔后，其刀柄后部的拉钉便被送到主轴内拉杆的前端，当接到夹紧信号时，将压力油通入主轴尾部的油缸左腔，活塞向右移动，拉杆在碟形弹簧的作用下也向右移动，其前端圆周上的钢球在主轴锥孔的逼迫下收缩分布直径，将刀柄拉钉紧紧拉住。

4. In the heating system, the heating cover and the heating preservation cotton should be made a body, the power of the heating cover shoulde be used adequately. In the feeding-in system, the shape of the feeding-in facility changes headstand four-pyramid by the headstand cone, it may prevent the appearance of the dead angle and increase the feeding-in quantity. In the hydraulic system, uniting the actual movement situation, the limit switch may be used to control whether the precompression rammer arrives the right position instead of the pressure switch, and we can promptly discovere whether the precompression room exists stopping-up situation and take the corresponding measure.
    加热系统中加热套和保温棉做成一体，加热套的功率应充分利用；进料系统中，进料斗的形状由倒置的四棱锥台改为倒置的圆锥台，可以防止死角的出现，增加进料量；液压系统结合实际运行情况，用行程开关替代压力继电器来控制预压冲杆是否到位，可以及时发现预压室是否有堵塞情况，以便采取相应措施。

5.

5. The electrode tip is in a cone shape with radius of 0.5mm which attached to the electrode base with spring, providing cushion for better contact with human skin.
    探针内附弹簧与探针套筒组成具弹性的电极，能使电极与皮肤有较理想的接触。

6. The results indicate that this system can effectively and automatically measure thread medium diameter, cone, thread pitch and pipe-thread shape so as to the problem of integrated measurement of petroleum pipe threads agilely.
    结果表明，该系统可以高效自动地测量螺纹中径、锥度、螺距和管螺纹形状，可便捷地解决石油管螺纹的综合测量问题。

7. Through morphological analysis between male sterile plant and male fertile plant in the alabastrum period as well as in flowering period, one morphological mark was found that the alabastrum of male sterile plant was in cone shape; the alabastrum of male fertile plant was cylindraceous. The male sterile alabastrum and male fertile alabastrum were significantly different. The petal of male sterile is filiform but not lingulate and tubular, the normal one was just the opposite.
    通过在蕾期和盛花期对不育系和可育系的形态性状进行分析，找到了一个与育性相关的形态标记，即不育系的花蕾呈圆锥状，而可育系花蕾呈圆柱状，二者形态差异极显著；花开放后，不育系的花瓣丝状化，没有舌状花和管状花之分，而正常可育系花序外围是舌状花，内部是管状花。

8. This design uses side runner, the spruce uses the cold-slug well with cone-shape type using cone-shape to pull the spruce solidified materials when ejecting.
    采用侧浇口，主流道采用的是倒锥形冷料穴，脱模时通过倒锥将主流道凝料拉出。

9. The shape of the material used for cutting is frustum of a cone in Masteel Wheel Company.
    用一种局部优化算法代替变异算子以提高算法的爬山能力。3。

10. cone shape的解释

10. Through the electrical emulation with ANSYS, it is found that the pyramidal face shape of stress cone impacts deeply the electrical field which falls down following with the radius of curvature increasing. And the structure of stress cone is optimized by which the electrical field is improved effectively after analyzing the influence of dielectric and mass resistivity of material to the stress cone electrical field.
    通过ANSYS分析软件对应力锥终端的电场仿真，发现应力锥锥面形状对终端电场分布影响较大，随曲率半径增大，各主要部位电场强度呈下降趋势；分析了应力锥材料的介电性能和体积电阻率对终端电场分布的影响，优化了应力锥结构，最大限度地改善、缓解了终端应力锥区域的电应力集中，有效地提高了电缆终端的电气性能。

11. Under the condition of high-pressure formation, the valve core of the cone-shape choke valve in the choke-line manifold is often prone to breaking, which can not meet the demand of safe well-control operation.
      在高压地层条件下，节流管汇中的锥形节流阀经常发生阀心断裂事故，不能满足井控作业安全生产的要求，需要选用孔板式节流阀进行压井作业。

12. The fluidization behavior of glass beads is investigated in superheated steam fluidized bed with a cone shape and the bottom diameter of 120mm for research about the influences of operating temperature and pressure on minimum fluidization velocity.
      在底部直径为120 mm的锥型流化床中，以玻璃珠为流化颗粒，过热蒸汽为流化介质，研究了固体颗粒在过热蒸汽流化床中的流化特性，考察了操作温度和压力对临界流化速度的影响结果表明，过热蒸汽流化床的流化行为与热空气相似，临界流化速度随床层温度的升高而减小，随床内压力的增大而减小，在相同温度条件下，过热蒸汽流化床的临界流化速度比热空气大

13. By friction round shape of the different levels can be divided into cylindrical friction wheel drive, cylindrical trough friction wheel drive, three kinds of cone friction wheel drive.
      按摩擦轮形状的不同，可分为圆柱平摩擦轮传动、圆柱槽摩擦轮传动、圆锥摩擦轮传动三种。

14. The paper also discusses the variations of the shape of the intersection curve and the loci of the special points on it when position of intersection and sizes of the cone and the cylinder are altered.
      圆柱体与圆锥体垂直相交是目前教材中常用的讲授例题之一，对该例中相贯线上某些特殊点的求法，有些教材中的讲述值得商讨。

15. In this paper, a concrete-made artificial reef model with the shape of hexahedral cone was put into the experimental tank to observe the attraction effects of the artificial reef model on Plectorhynchus cinctus under three illumination conditions of natural illumination, 55 W and 26 W.
      为了解不同光照条件下人工鱼礁的集鱼效果，观察了自然光、55 W和26 W 3种光照条件下试验水槽内六面锥型罩式水泥人工鱼礁模型对花尾胡椒鲷的诱集效果。

16. Fuel jets injected from multi-hole nozzle impinge on inclined orientation surface and spread along the surface as shape of sectors, by which a quasi-cone shape spray is formed. The spray penetration can be regulated according to the adjustment of impingement angle in design. Impingement spray systems are classified into three kinds according to different orientation surface shapes, which are outer cone-surface, inner cone-surface and multi-piece impingement spray system respectively. Based on the percentage of impinged fuel, the spray is categorized as whole-impingement spray and half-impingement spray.
      2利用油束撞壁雾化原理，开发了以多孔油嘴和碰撞导向装置为核心的柴油机近距撞壁准伞状喷雾燃烧系统，即从喷孔喷出的油束以一定夹角撞击设置在油嘴头部周围的导向斜壁，碰撞后的油束沿导向壁面发展并扩散成近似的伞状喷雾分布，喷雾贯穿距可以通过调整油束与导向壁面的撞壁夹角进行设定。

17. Standing on the prow was a tall man, of a dark complexion, who saw with dilating eyes that they were approaching a dark mass of land in the shape of a cone, which rose from the midst of the waves like the hat of a Catalan
      船头上站着一个身材高大、肤色浅黑的男子，他大睁着的眼睛看着他们渐渐接近的一片乌压压的陆地，那块陆地矗立在万顷波涛之中，象是一顶硕大无朋的迦太兰人的圆锥形的帽子。

18. The electric carving sculpture needle shape determines the network is cone and half of the inking cannot be transferred
      电雕雕刻针的形状决定了网坑是锥字体，因此有一半的墨量无法转移

19. Now to plank the tail cone and I''ll use blue foam to shape the bow.
      现在木板尾锥，我将使用蓝色泡沫形成低头。

20. The nebula''s unique shape comes from gas and dust emitted in cone-shaped bursts from the dying star at its center.
      它的外形唯一的来源是气体和灰尘的散发呈锥形的爆发，那是一棵死亡之星的中心的喷发。